Vivilon
 
VIVILON Porous Primer ™
 
What it is:
Porous Primer is a penetrating primer coat, required when applying VIVILON™ top coat over any porous substrate. This clear, low solids coating is formulated for optimum ease of penetration deep into and absorbtion by the open pores of the substrate. This provides for the important sealing off of the surface porosity and provides the necessary solid foundation for top coating with VIVILON™.
 
Where is it used:

Acting almost like a "sanding sealer", Porous Primer prepares surfaces like brick, stucco, EIFS, unglazed tile, concrete, unpainted wood and stone for effective, long lasting restorative sealing and protection. For some very porous surfaces, a second coat of primer may be required.

How Can I Buy It

VIVILON makes it simple, quick and easy to purchase our products. By clicking the BUY NOW button below, you will be taken to our PayPal Secure Payment Shopping Center where you will be able to buy whatever you want, using whatever means of payment you want. Credit Cards (Visa, Mastercard, American Express or Discover), Debit Cards, E-Checks or PayPal. Your order will be packed and shipped the next day at no extra charge. That's right, the shipping cost is paid by VIVILON!

IMPORTANT: All information used to process your order is secure with PayPal and we never see it. Of course, during business hours, you can always call us to check on your order or have any question answered. If you are ready to begin shopping, click on the button below. Thank You!

One Gallon
Five Gallons
 
PRODUCT DATA SHEET
 
Solids Content: 15%
 
Weight Per Gallon: 7.5 Pounds
 
Coverage Rate: 800 Square Feet Per Gallon (SFPG)
 
Time to Touch Dry: 10 Minutes At 70 Degrees F; 50% Relative Humidity
 
Time To Full Cure: 5 Days
 
Dry Time Between Coats: 1 Hour ( At 70 Degrees F; 50% Relative Humidity )
 
Recommended Wet Film Thickness (WFT) Per Coat2 Mils or 51 Microns
 
Approximate Dry Film Thickness (DFT) Per Coat: .3 Mils or 8 Microns
  
Theoretical Coverage @ .3 mil (DFT) Per Coat: 800 Square Feet
 
Typical 60 Degree Gloss: 90
 
Viscosity Using #2 Zahn Cup: 22 Seconds
 
Application Methods:
Conventional or HVLP compressed air, HVLP turbine, airless, air assisted airless sprayers, brush, short nap roller, sponge or squeegee/spreader.
 
Recommended Spray Gun Setups:
  • Siphon Feed: 2.0 mm to 2.2 mm (.0787 to .0866)
  • Gravity Feed: 1.4 mm to 1.5 mm (.0551 to .0630)
  • Pressure Feed: .8 mm to 1.0 mm (.0315 to .0394)
 
Sanding & Buffing:
Not normally applicable.
 
Equipment Cleanup:
Toluene, Xylene or Lacquer Thinner
 
For Faster Dry Time:
Add from 1 to 3 ounces of Xylene per quart of VIVILON™. Recommended whenever spraying below 50 degrees Fahrenheit. Be careful to add only the MINIMUM amount of solvent absolutely necessary. If the coating dries too quickly, it will harden before it has a chance to penetrate fully.
 
To Slow Dry Time:
Add 1 to 3 ounces of VIVILON Retarder per quart of Porous Primer. Recommended when spraying above 85 degrees Fahrenheit or to extend open time when brushing or rolling product.
 
To Prevent Blushing on Humid Days:
Add 1 to 3 ounces of VIVILON Retarder per quart of Porous Primer.
 
Maintenance Cleaning:
Not applicable. Porous Primer is always top coated with VIVILON. To wash VIVILON™ coated surfaces, after full cure, use a neutral cleaner and a soft brush. DO NOT USE hot water, steam, highly acidic or caustic materials. They are not needed or advised.
 
 
IMPORTANT:
The Material Safety Data Sheet (MSDS) and the container labels for these products contain additional important health and safety information, which you should read carefully and follow before using this product.
 
 
Beauty and Protection Perfection